The growth of command line options, 1979-Present
The first of McIlroy's dicta is often paraphrased as "do one thing and do it well", which is shortened from "Make each program do one thing well. To do a new job, build afresh rather than complicate old programs by adding new 'features.'" [ . . . ]
If you open up a manpage for ls on mac, you'll see that it starts with
ls [-ABCFGHLOPRSTUW@abcdefghiklmnopqrstuwx1] [file ...]
That is, the one-letter flags to ls include every lowercase letter except for {jvyz}, 14 uppercase letters, plus @ and 1. That's 22 + 14 + 2 = 38 single-character options alone.
On ubuntu 17, if you read the manpage for coreutils ls, you don't get a nice summary of options, but you'll see that ls has 58 options (including --help and --version).
To see if ls is an aberration or if it's normal to have commands that do this much stuff, we can look at some common commands, sorted by frequency of use.
(see article for interesting table.)
We can see that the number of command line options has dramatically increased over time; entries tend to get darker going to the right (more options) and there are no cases where entries get lighter (fewer options).
Everything was small and my heart sinks for Linux when I see the size [inaudible]. The same utilities that used to fit in eight k[ilobytes] are a meg now. And the manual page, which used to really fit on, which used to really be a manual page, is now a small volume with a thousand options... We used to sit around in the UNIX room saying "what can we throw out? Why is there this option?" It's usually, it's often because there's some deficiency in the basic design -- you didn't really hit the right design point. Instead of putting in an option, figure out why, what was forcing you to add that option. This viewpoint, which was imposed partly because there was very small hardware ... has been lost and we're not better off for it.
[ . . . . ] Another reason commands now have more options is that people have added convenience flags for functionality that could have been done by cobbling together a series of commands. These go all the way back to v7 unix, where ls has an option to reverse the sort order (which could have been done by passing the output to tac).
Over time, more convenience options have been added. For example, to pick a command that originally has zero options, mv can move and create a backup (three options; two are different ways to specify a backup, one of which takes an argument and the other of which takes zero explicit arguments and reads an implicit argument from the VERSION_CONTROL environment variable; one option allows overriding the default backup suffix). mv now also has options to never overwrite and to only overwrite if the file is newer.
mkdir is another program that used to have no options where, excluding security things for SELinux or SMACK as well as help and version options, the added options are convenience flags: setting the permissions of the new directory and making parent directories if they don't exist.
[ . . . ] unlike with a GUI, adding these options doesn't clutter up the interface.
(emphasis added)
No worry, systemd will guide us back to the true Unix Microsoft way.
(Score: 2) by Gaaark on Wednesday March 04 2020, @04:58AM (38 children)
What's the man-page for systemd look like...the telephone book?
--- Please remind me if I haven't been civil to you: I'm channeling MDC. ---Gaaark 2.0 ---
(Score: 2) by barbara hudson on Wednesday March 04 2020, @05:03AM (12 children)
SoylentNews is social media. Says so right in the slogan. Soylentnews is people, not tech.
(Score: 2) by coolgopher on Wednesday March 04 2020, @06:22AM (11 children)
His "Programming Windows 95" was a good read as I recall it.
That said, I still don't want a portion of Windows with my Linux, thank you very much.
(Score: 2) by barbara hudson on Wednesday March 04 2020, @12:20PM (10 children)
SoylentNews is social media. Says so right in the slogan. Soylentnews is people, not tech.
(Score: 2) by DannyB on Wednesday March 04 2020, @05:47PM (2 children)
In a large sense yes. On an individual level, no. And there are a lot of individuals. Remember the rise of open source vs the mighty unassailable Microsoft. Or the rise of these pesky "microcomputer" toy things vs the mighty IBM.
For the most part, I expect the companies paying the bills to make choices based on what makes economic sense. But insanity sometimes prevails. (not intending to inject politics. /sarc)
To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 2) by barbara hudson on Wednesday March 04 2020, @07:30PM (1 child)
SoylentNews is social media. Says so right in the slogan. Soylentnews is people, not tech.
(Score: -1, Troll) by Anonymous Coward on Wednesday March 04 2020, @09:14PM
Why is linus such a fag?
(Score: 2) by coolgopher on Thursday March 05 2020, @01:12AM (4 children)
Meh. If I have to I'll build from scratch or via buildroot. Or go back to FreeBSD. And if I *really* have to, I'll fork the kernel and stick to old and/or open hardware (RISC-V, hello!).
In the meantime I'll keep pointing people at the excellent work done by e.g. Devuan [devuan.org] to keep stuff systemd free.
(Score: 2) by barbara hudson on Thursday March 05 2020, @02:01AM (3 children)
SoylentNews is social media. Says so right in the slogan. Soylentnews is people, not tech.
(Score: 2) by coolgopher on Thursday March 05 2020, @03:35AM (2 children)
I have now. 27, not counting my shells.
(Score: 2) by barbara hudson on Thursday March 05 2020, @04:48PM (1 child)
SoylentNews is social media. Says so right in the slogan. Soylentnews is people, not tech.
(Score: 2) by coolgopher on Friday March 06 2020, @01:28AM
Well, this ain't Ubuntu. This is a system which uses runit [smarden.org] as init, and I haven't installed a bunch of unnecessary junk on this system.
In my process list there are 53 kernel threads listed, 12 daemons, 10 service monitors (runsv), 4 supporting log daemons, and the init process. And if you're curious why there are fewer service monitors than daemons, it's the two dhclient processes that aren't monitored.
(Score: 0) by Anonymous Coward on Thursday March 05 2020, @02:30AM
This is natural and logical. As a manager I want productivity and my sysadmins being the hubris-driven creatures they are want to type less and do more.
So eventually it is easier for all concerned to have cp have a new option "-r" than the magical incantations of old.. something like:
find /path -some-magic-markers-and-options-to-select-files-or-folders | cpio another-series-of-pretty-obscure-magic-flags
(Score: 0) by Anonymous Coward on Thursday March 05 2020, @06:13PM
That'll wind up being officially referred to as "homie-D".
(Score: 0) by Anonymous Coward on Wednesday March 04 2020, @05:03AM
thatd be so Unix.
manpage. lol.
(Score: 4, Funny) by Anonymous Coward on Wednesday March 04 2020, @05:14AM (17 children)
SYSTEMD(1) systemd SYSTEMD(1)
NAME
systemd, init - systemd system and service manager
SYNOPSIS
systemd [OPTIONS...]
init [OPTIONS...] {COMMAND}
DESCRIPTION
systemd is a system and service manager for Linux operating systems.
When run as first process on boot (as PID 1), it acts as init system
that brings up and maintains userspace services.
For compatibility with SysV, if systemd is called as init and a PID
that is not 1, it will execute telinit and pass all command line
arguments unmodified. That means init and telinit are mostly
equivalent when invoked from normal login sessions. See telinit(8)
for more information.
When run as a system instance, systemd interprets the configuration
file system.conf and the files in system.conf.d directories; when run
as a user instance, systemd interprets the configuration file
user.conf and the files in user.conf.d directories. See
systemd-system.conf(5) for more information.
OPTIONS
The following options are understood:
--test
Determine startup sequence, dump it and exit. This is an option
useful for debugging only.
--dump-configuration-items
Dump understood unit configuration items. This outputs a terse
but complete list of configuration items understood in unit
definition files.
--unit=
Set default unit to activate on startup. If not specified,
defaults to default.target.
--system, --user
For --system, tell systemd to run a system instance, even if the
process ID is not 1, i.e. systemd is not run as init process.
--user does the opposite, running a user instance even if the
process ID is 1. Normally, it should not be necessary to pass
these options, as systemd automatically detects the mode it is
started in. These options are hence of little use except for
debugging. Note that it is not supported booting and maintaining
a full system with systemd running in --system mode, but PID not
1. In practice, passing --system explicitly is only useful in
conjunction with --test.
--dump-core
Enable core dumping on crash. This switch has no effect when
running as user instance. This setting may also be enabled during
boot on the kernel command line via the systemd.dump_core=
option, see below.
--crash-vt=VT
Switch to a specific virtual console (VT) on crash. Takes a
positive integer in the range 1–63, or a boolean argument. If an
integer is passed, selects which VT to switch to. If yes, the VT
kernel messages are written to is selected. If no, no VT switch
is attempted. This switch has no effect when running as user
instance. This setting may also be enabled during boot, on the
kernel command line via the systemd.crash_vt= option, see below.
--crash-shell
Run a shell on crash. This switch has no effect when running as
user instance. This setting may also be enabled during boot, on
the kernel command line via the systemd.crash_shell= option, see
below.
--crash-reboot
Automatically reboot the system on crash. This switch has no
effect when running as user instance. This setting may also be
enabled during boot, on the kernel command line via the
systemd.crash_reboot= option, see below.
--confirm-spawn
Ask for confirmation when spawning processes. This switch has no
effect when run as user instance.
--show-status=
Takes a boolean argument or the special value auto. If on, terse
unit status information is shown on the console during boot-up
and shutdown. If off, no such status information is shown. If set
to auto behavior is similar to off, except that it is
automatically switched to on, as soon as the first unit failure
or significant boot delay is encountered. This switch has no
effect when invoked as user instance. If specified, overrides
both the kernel command line setting systemd.show_status= (see
below) and the configuration file option ShowStatus=, see
systemd-system.conf(5).
--log-target=
Set log target. Argument must be one of console, journal, kmsg,
journal-or-kmsg, null.
--log-level=
Set log level. As argument this accepts a numerical log level or
the well-known syslog(3) symbolic names (lowercase): emerg,
alert, crit, err, warning, notice, info, debug.
--log-color=
Highlight important log messages. Argument is a boolean value. If
the argument is omitted, it defaults to true.
--log-location=
Include code location in log messages. This is mostly relevant
for debugging purposes. Argument is a boolean value. If the
argument is omitted it defaults to true.
--default-standard-output=, --default-standard-error=
Sets the default output or error output for all services and
sockets, respectively. That is, controls the default for
StandardOutput= and StandardError= (see systemd.exec(5) for
details). Takes one of inherit, null, tty, journal,
journal+console, syslog, syslog+console, kmsg, kmsg+console. If
the argument is omitted --default-standard-output= defaults to
journal and --default-standard-error= to inherit.
--machine-id=
Override the machine-id set on the hard drive, useful for network
booting or for containers. May not be set to all zeros.
-h, --help
Print a short help text and exit.
--version
Print a short version string and exit.
CONCEPTS
systemd provides a dependency system between various entities called
"units" of 11 different types. Units encapsulate various objects that
are relevant for system boot-up and maintenance. The majority of
units are configured in unit configuration files, whose syntax and
basic set of options is described in systemd.unit(5), however some
are created automatically from other configuration, dynamically from
system state or programmatically at runtime. Units may be "active"
(meaning started, bound, plugged in, ..., depending on the unit type,
see below), or "inactive" (meaning stopped, unbound, unplugged, ...),
as well as in the process of being activated or deactivated, i.e.
between the two states (these states are called "activating",
"deactivating"). A special "failed" state is available as well, which
is very similar to "inactive" and is entered when the service failed
in some way (process returned error code on exit, or crashed, or an
operation timed out). If this state is entered, the cause will be
logged, for later reference. Note that the various unit types may
have a number of additional substates, which are mapped to the five
generalized unit states described here.
The following unit types are available:
1. Service units, which start and control daemons and the processes
they consist of. For details, see systemd.service(5).
2. Socket units, which encapsulate local IPC or network sockets in
the system, useful for socket-based activation. For details about
socket units, see systemd.socket(5), for details on socket-based
activation and other forms of activation, see daemon(7).
3. Target units are useful to group units, or provide well-known
synchronization points during boot-up, see systemd.target(5).
4. Device units expose kernel devices in systemd and may be used to
implement device-based activation. For details, see
systemd.device(5).
5. Mount units control mount points in the file system, for details
see systemd.mount(5).
6. Automount units provide automount capabilities, for on-demand
mounting of file systems as well as parallelized boot-up. See
systemd.automount(5).
7. Timer units are useful for triggering activation of other units
based on timers. You may find details in systemd.timer(5).
8. Swap units are very similar to mount units and encapsulate memory
swap partitions or files of the operating system. They are
described in systemd.swap(5).
9. Path units may be used to activate other services when file
system objects change or are modified. See systemd.path(5).
10. Slice units may be used to group units which manage system
processes (such as service and scope units) in a hierarchical
tree for resource management purposes. See systemd.slice(5).
11. Scope units are similar to service units, but manage foreign
processes instead of starting them as well. See systemd.scope(5).
Units are named as their configuration files. Some units have special
semantics. A detailed list is available in systemd.special(7).
systemd knows various kinds of dependencies, including positive and
negative requirement dependencies (i.e. Requires= and Conflicts=) as
well as ordering dependencies (After= and Before=). NB: ordering and
requirement dependencies are orthogonal. If only a requirement
dependency exists between two units (e.g. foo.service requires
bar.service), but no ordering dependency (e.g. foo.service after
bar.service) and both are requested to start, they will be started in
parallel. It is a common pattern that both requirement and ordering
dependencies are placed between two units. Also note that the
majority of dependencies are implicitly created and maintained by
systemd. In most cases, it should be unnecessary to declare
additional dependencies manually, however it is possible to do this.
Application programs and units (via dependencies) may request state
changes of units. In systemd, these requests are encapsulated as
'jobs' and maintained in a job queue. Jobs may succeed or can fail,
their execution is ordered based on the ordering dependencies of the
units they have been scheduled for.
On boot systemd activates the target unit default.target whose job is
to activate on-boot services and other on-boot units by pulling them
in via dependencies. Usually, the unit name is just an alias
(symlink) for either graphical.target (for fully-featured boots into
the UI) or multi-user.target (for limited console-only boots for use
in embedded or server environments, or similar; a subset of
graphical.target). However, it is at the discretion of the
administrator to configure it as an alias to any other target unit.
See systemd.special(7) for details about these target units.
Processes systemd spawns are placed in individual Linux control
groups named after the unit which they belong to in the private
systemd hierarchy. (see cgroups.txt[1] for more information about
control groups, or short "cgroups"). systemd uses this to effectively
keep track of processes. Control group information is maintained in
the kernel, and is accessible via the file system hierarchy (beneath
/sys/fs/cgroup/systemd/), or in tools such as systemd-cgls(1) or
ps(1) (ps xawf -eo pid,user,cgroup,args is particularly useful to
list all processes and the systemd units they belong to.).
systemd is compatible with the SysV init system to a large degree:
SysV init scripts are supported and simply read as an alternative
(though limited) configuration file format. The SysV /dev/initctl
interface is provided, and compatibility implementations of the
various SysV client tools are available. In addition to that, various
established Unix functionality such as /etc/fstab or the utmp
database are supported.
systemd has a minimal transaction system: if a unit is requested to
start up or shut down it will add it and all its dependencies to a
temporary transaction. Then, it will verify if the transaction is
consistent (i.e. whether the ordering of all units is cycle-free). If
it is not, systemd will try to fix it up, and removes non-essential
jobs from the transaction that might remove the loop. Also, systemd
tries to suppress non-essential jobs in the transaction that would
stop a running service. Finally it is checked whether the jobs of the
transaction contradict jobs that have already been queued, and
optionally the transaction is aborted then. If all worked out and the
transaction is consistent and minimized in its impact it is merged
with all already outstanding jobs and added to the run queue.
Effectively this means that before executing a requested operation,
systemd will verify that it makes sense, fixing it if possible, and
only failing if it really cannot work.
Systemd contains native implementations of various tasks that need to
be executed as part of the boot process. For example, it sets the
hostname or configures the loopback network device. It also sets up
and mounts various API file systems, such as /sys or /proc.
For more information about the concepts and ideas behind systemd,
please refer to the Original Design Document[2].
Note that some but not all interfaces provided by systemd are covered
by the Interface Stability Promise[3].
Units may be generated dynamically at boot and system manager reload
time, for example based on other configuration files or parameters
passed on the kernel command line. For details, see
systemd.generator(7).
Systems which invoke systemd in a container or initrd environment
should implement the Container Interface[4] or initrd Interface[5]
specifications, respectively.
DIRECTORIES
System unit directories
The systemd system manager reads unit configuration from various
directories. Packages that want to install unit files shall place
them in the directory returned by pkg-config systemd
--variable=systemdsystemunitdir. Other directories checked are
/usr/local/lib/systemd/system and /usr/lib/systemd/system. User
configuration always takes precedence. pkg-config systemd
--variable=systemdsystemconfdir returns the path of the system
configuration directory. Packages should alter the content of
these directories only with the enable and disable commands of
the systemctl(1) tool. Full list of directories is provided in
systemd.unit(5).
User unit directories
Similar rules apply for the user unit directories. However, here
the XDG Base Directory specification[6] is followed to find
units. Applications should place their unit files in the
directory returned by pkg-config systemd
--variable=systemduserunitdir. Global configuration is done in
the directory reported by pkg-config systemd
--variable=systemduserconfdir. The enable and disable commands of
the systemctl(1) tool can handle both global (i.e. for all users)
and private (for one user) enabling/disabling of units. Full list
of directories is provided in systemd.unit(5).
SysV init scripts directory
The location of the SysV init script directory varies between
distributions. If systemd cannot find a native unit file for a
requested service, it will look for a SysV init script of the
same name (with the .service suffix removed).
SysV runlevel link farm directory
The location of the SysV runlevel link farm directory varies
between distributions. systemd will take the link farm into
account when figuring out whether a service shall be enabled.
Note that a service unit with a native unit configuration file
cannot be started by activating it in the SysV runlevel link
farm.
SIGNALS
SIGTERM
Upon receiving this signal the systemd system manager serializes
its state, reexecutes itself and deserializes the saved state
again. This is mostly equivalent to systemctl daemon-reexec.
systemd user managers will start the exit.target unit when this
signal is received. This is mostly equivalent to systemctl --user
start exit.target.
SIGINT
Upon receiving this signal the systemd system manager will start
the ctrl-alt-del.target unit. This is mostly equivalent to
systemctl start ctl-alt-del.target. If this signal is received
more than 7 times per 2s, an immediate reboot is triggered. Note
that pressing Ctrl-Alt-Del on the console will trigger this
signal. Hence, if a reboot is hanging, pressing Ctrl-Alt-Del more
than 7 times in 2s is a relatively safe way to trigger an
immediate reboot.
systemd user managers treat this signal the same way as SIGTERM.
SIGWINCH
When this signal is received the systemd system manager will
start the kbrequest.target unit. This is mostly equivalent to
systemctl start kbrequest.target.
This signal is ignored by systemd user managers.
SIGPWR
When this signal is received the systemd manager will start the
sigpwr.target unit. This is mostly equivalent to systemctl start
sigpwr.target.
SIGUSR1
When this signal is received the systemd manager will try to
reconnect to the D-Bus bus.
SIGUSR2
When this signal is received the systemd manager will log its
complete state in human-readable form. The data logged is the
same as printed by systemd-analyze dump.
SIGHUP
Reloads the complete daemon configuration. This is mostly
equivalent to systemctl daemon-reload.
SIGRTMIN+0
Enters default mode, starts the default.target unit. This is
mostly equivalent to systemctl start default.target.
SIGRTMIN+1
Enters rescue mode, starts the rescue.target unit. This is mostly
equivalent to systemctl isolate rescue.target.
SIGRTMIN+2
Enters emergency mode, starts the emergency.service unit. This is
mostly equivalent to systemctl isolate emergency.service.
SIGRTMIN+3
Halts the machine, starts the halt.target unit. This is mostly
equivalent to systemctl start halt.target.
SIGRTMIN+4
Powers off the machine, starts the poweroff.target unit. This is
mostly equivalent to systemctl start poweroff.target.
SIGRTMIN+5
Reboots the machine, starts the reboot.target unit. This is
mostly equivalent to systemctl start reboot.target.
SIGRTMIN+6
Reboots the machine via kexec, starts the kexec.target unit. This
is mostly equivalent to systemctl start kexec.target.
SIGRTMIN+13
Immediately halts the machine.
SIGRTMIN+14
Immediately powers off the machine.
SIGRTMIN+15
Immediately reboots the machine.
SIGRTMIN+16
Immediately reboots the machine with kexec.
SIGRTMIN+20
Enables display of status messages on the console, as controlled
via systemd.show_status=1 on the kernel command line.
SIGRTMIN+21
Disables display of status messages on the console, as controlled
via systemd.show_status=0 on the kernel command line.
SIGRTMIN+22, SIGRTMIN+23
Sets the log level to "debug" (or "info" on SIGRTMIN+23), as
controlled via systemd.log_level=debug (or systemd.log_level=info
on SIGRTMIN+23) on the kernel command line.
SIGRTMIN+24
Immediately exits the manager (only available for --user
instances).
SIGRTMIN+26, SIGRTMIN+27, SIGRTMIN+28
Sets the log target to "journal-or-kmsg" (or "console" on
SIGRTMIN+27, "kmsg" on SIGRTMIN+28), as controlled via
systemd.log_target=journal-or-kmsg (or systemd.log_target=console
on SIGRTMIN+27 or systemd.log_target=kmsg on SIGRTMIN+28) on the
kernel command line.
ENVIRONMENT
$SYSTEMD_LOG_LEVEL
systemd reads the log level from this environment variable. This
can be overridden with --log-level=.
$SYSTEMD_LOG_TARGET
systemd reads the log target from this environment variable. This
can be overridden with --log-target=.
$SYSTEMD_LOG_COLOR
Controls whether systemd highlights important log messages. This
can be overridden with --log-color=.
$SYSTEMD_LOG_LOCATION
Controls whether systemd prints the code location along with log
messages. This can be overridden with --log-location=.
$XDG_CONFIG_HOME, $XDG_CONFIG_DIRS, $XDG_DATA_HOME, $XDG_DATA_DIRS
The systemd user manager uses these variables in accordance to
the XDG Base Directory specification[6] to find its
configuration.
$SYSTEMD_UNIT_PATH
Controls where systemd looks for unit files.
$SYSTEMD_SYSVINIT_PATH
Controls where systemd looks for SysV init scripts.
$SYSTEMD_SYSVRCND_PATH
Controls where systemd looks for SysV init script runlevel link
farms.
$SYSTEMD_COLORS
The value must be a boolean. Controls whether colorized output
should be generated. This can be specified to override the
decision that systemd makes based on $TERM and what the console
is connected to.
$LISTEN_PID, $LISTEN_FDS, $LISTEN_FDNAMES
Set by systemd for supervised processes during socket-based
activation. See sd_listen_fds(3) for more information.
$NOTIFY_SOCKET
Set by systemd for supervised processes for status and start-up
completion notification. See sd_notify(3) for more information.
KERNEL COMMAND LINE
When run as system instance systemd parses a number of kernel command
line arguments[7]:
systemd.unit=, rd.systemd.unit=
Overrides the unit to activate on boot. Defaults to
default.target. This may be used to temporarily boot into a
different boot unit, for example rescue.target or
emergency.service. See systemd.special(7) for details about these
units. The option prefixed with "rd." is honored only in the
initial RAM disk (initrd), while the one that is not prefixed
only in the main system.
systemd.dump_core
Takes a boolean argument or enables the option if specified
without an argument. If enabled, the systemd manager (PID 1)
dumps core when it crashes. Otherwise, no core dump is created.
Defaults to enabled.
systemd.crash_chvt
Takes a positive integer, or a boolean argument. Can be also
specified without an argument, with the same effect as a positive
boolean. If a positive integer (in the range 1–63) is specified,
the system manager (PID 1) will activate the specified virtual
terminal (VT) when it crashes. Defaults to disabled, meaning that
no such switch is attempted. If set to enabled, the VT the kernel
messages are written to is selected.
systemd.crash_shell
Takes a boolean argument or enables the option if specified
without an argument. If enabled, the system manager (PID 1)
spawns a shell when it crashes, after a 10s delay. Otherwise, no
shell is spawned. Defaults to disabled, for security reasons, as
the shell is not protected by password authentication.
systemd.crash_reboot
Takes a boolean argument or enables the option if specified
without an argument. If enabled, the system manager (PID 1) will
reboot the machine automatically when it crashes, after a 10s
delay. Otherwise, the system will hang indefinitely. Defaults to
disabled, in order to avoid a reboot loop. If combined with
systemd.crash_shell, the system is rebooted after the shell
exits.
systemd.confirm_spawn
Takes a boolean argument or a path to the virtual console where
the confirmation messages should be emitted. Can be also
specified without an argument, with the same effect as a positive
boolean. If enabled, the system manager (PID 1) asks for
confirmation when spawning processes using /dev/console. If a
path or a console name (such as "ttyS0") is provided, the virtual
console pointed to by this path or described by the give name
will be used instead. Defaults to disabled.
systemd.show_status
Takes a boolean argument or the constant auto. Can be also
specified without an argument, with the same effect as a positive
boolean. If enabled, the systemd manager (PID 1) shows terse
service status updates on the console during bootup. auto
behaves like false until a unit fails or there is a significant
delay in boot. Defaults to enabled, unless quiet is passed as
kernel command line option, in which case it defaults to auto. If
specified overrides the system manager configuration file option
ShowStatus=, see systemd-system.conf(5). However, the process
command line option --show-status= takes precedence over both
this kernel command line option and the configuration file
option.
systemd.log_target=, systemd.log_level=, systemd.log_location=,
systemd.log_color
Controls log output, with the same effect as the
$SYSTEMD_LOG_TARGET, $SYSTEMD_LOG_LEVEL, $SYSTEMD_LOG_LOCATION,
$SYSTEMD_LOG_COLOR environment variables described above.
systemd.log_color can be specified without an argument, with the
same effect as a positive boolean.
systemd.default_standard_output=, systemd.default_standard_error=
Controls default standard output and error output for services,
with the same effect as the --default-standard-output= and
--default-standard-error= command line arguments described above,
respectively.
systemd.setenv=
Takes a string argument in the form VARIABLE=VALUE. May be used
to set default environment variables to add to forked child
processes. May be used more than once to set multiple variables.
systemd.machine_id=
Takes a 32 character hex value to be used for setting the
machine-id. Intended mostly for network booting where the same
machine-id is desired for every boot.
systemd.unified_cgroup_hierarchy
When specified without an argument or with a true argument,
enables the usage of unified cgroup hierarchy[8]
(a.k.a. cgroups-v2). When specified with a false argument, fall
back to hybrid or full legacy cgroup hierarchy.
If this option is not specified, the default behaviour is
determined during compilation (the --with-default-hierarchy=
option). If the kernel does not support unified cgroup hierarchy,
the legacy hierarchy will be used even if this option is
specified.
systemd.legacy_systemd_cgroup_controller
Takes effect if the full unified cgroup hierarchy is not used
(see previous option). When specified without an argument or with
a true argument, disables the use of "hybrid" cgroup hierarchy
(i.e. a cgroups-v2 tree used for systemd, and legacy cgroup
hierarchy[9], a.k.a. cgroups-v1, for other controllers), and
forces a full "legacy" mode. When specified with a false
argument, enables the use of "hybrid" hierarchy.
If this option is not specified, the default behaviour is
determined during compilation (the --with-default-hierarchy=
option). If the kernel does not support unified cgroup hierarchy,
the legacy hierarchy will be used even if this option is
specified.
quiet
Turn off status output at boot, much like
systemd.show_status=false would. Note that this option is also
read by the kernel itself and disables kernel log output. Passing
this option hence turns off the usual output from both the system
manager and the kernel.
debug
Turn on debugging output. This is equivalent to
systemd.log_level=debug. Note that this option is also read by
the kernel itself and enables kernel debug output. Passing this
option hence turns on the debug output from both the system
manager and the kernel.
emergency, rd.emergency, -b
Boot into emergency mode. This is equivalent to
systemd.unit=emergency.target or
rd.systemd.unit=emergency.target, respectively, and provided for
compatibility reasons and to be easier to type.
rescue, rd.rescue, single, s, S, 1
Boot into rescue mode. This is equivalent to
systemd.unit=rescue.target or rd.systemd.unit=rescue.target,
respectively, and provided for compatibility reasons and to be
easier to type.
2, 3, 4, 5
Boot into the specified legacy SysV runlevel. These are
equivalent to systemd.unit=runlevel2.target,
systemd.unit=runlevel3.target, systemd.unit=runlevel4.target, and
systemd.unit=runlevel5.target, respectively, and provided for
compatibility reasons and to be easier to type.
locale.LANG=, locale.LANGUAGE=, locale.LC_CTYPE=, locale.LC_NUMERIC=,
locale.LC_TIME=, locale.LC_COLLATE=, locale.LC_MONETARY=,
locale.LC_MESSAGES=, locale.LC_PAPER=, locale.LC_NAME=,
locale.LC_ADDRESS=, locale.LC_TELEPHONE=, locale.LC_MEASUREMENT=,
locale.LC_IDENTIFICATION=
Set the system locale to use. This overrides the settings in
/etc/locale.conf. For more information, see locale.conf(5) and
locale(7).
For other kernel command line parameters understood by components of
the core OS, please refer to kernel-command-line(7).
SOCKETS AND FIFOS
/run/systemd/notify
Daemon status notification socket. This is an AF_UNIX datagram
socket and is used to implement the daemon notification logic as
implemented by sd_notify(3).
/run/systemd/private
Used internally as communication channel between systemctl(1) and
the systemd process. This is an AF_UNIX stream socket. This
interface is private to systemd and should not be used in
external projects.
/dev/initctl
Limited compatibility support for the SysV client interface, as
implemented by the systemd-initctl.service unit. This is a named
pipe in the file system. This interface is obsolete and should
not be used in new applications.
SEE ALSO
The systemd Homepage[10], systemd-system.conf(5), locale.conf(5),
systemctl(1), journalctl(1), systemd-notify(1), daemon(7),
sd-daemon(3), systemd.unit(5), systemd.special(5), pkg-config(1),
kernel-command-line(7), bootup(7), systemd.directives(7)
NOTES
1. cgroups.txt
https://www.kernel.org/doc/Documentation/cgroups/cgroups.txt [kernel.org]
2. Original Design Document
http://0pointer.de/blog/projects/systemd.html [0pointer.de]
3. Interface Stability Promise
https://www.freedesktop.org/wiki/Software/systemd/InterfaceStabilityPromise [freedesktop.org]
4. Container Interface
https://www.freedesktop.org/wiki/Software/systemd/ContainerInterface [freedesktop.org]
5. initrd Interface
https://www.freedesktop.org/wiki/Software/systemd/InitrdInterface [freedesktop.org]
6. XDG Base Directory specification
http://standards.freedesktop.org/basedir-spec/basedir-spec-latest.html [freedesktop.org]
7. If run inside a Linux container these arguments may be passed as
command line arguments to systemd itself, next to any of the
command line options listed in the Options section above. If run
outside of Linux containers, these arguments are parsed from
/proc/cmdline instead.
8. unified cgroup hierarchy
https://www.kernel.org/doc/Documentation/cgroup-v2.txt [kernel.org]
9. legacy cgroup hierarchy
https://www.kernel.org/doc/Documentation/cgroup-v1/ [kernel.org]
10. systemd Homepage
https://www.freedesktop.org/wiki/Software/systemd/ [freedesktop.org]
COLOPHON
This page is part of the systemd (systemd system and service manager)
project. Information about the project can be found at
⟨http://www.freedesktop.org/wiki/Software/systemd⟩. If you have a bug
report for this manual page, see
⟨http://www.freedesktop.org/wiki/Software/systemd/#bugreports⟩. This
page was obtained from the project's upstream Git repository
⟨https://github.com/systemd/systemd.git⟩ on 2019-11-19. (At that
time, the date of the most recent commit that was found in the repos‐
itory was 2019-11-19.) If you discover any rendering problems in
this HTML version of the page, or you believe there is a better or
more up-to-date source for the page, or you have corrections or
improvements to the information in this COLOPHON (which is not part
of the original manual page), send a mail to man-pages@man7.org
systemd 234 SYSTEMD(1)
(Score: 3, Funny) by Anonymous Coward on Wednesday March 04 2020, @05:43AM (4 children)
Just learned something new -- even ACs can post small books here!
(Score: 1, Disagree) by Anonymous Coward on Wednesday March 04 2020, @06:17AM (1 child)
Hey, it's a joke. Whoever modded parent "disagree" must have had their funny bone surgically removed.
(Score: 2, Disagree) by DannyB on Wednesday March 04 2020, @05:49PM
I have discovered some people are not born with funny bones.
To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 2) by DeathMonkey on Wednesday March 04 2020, @06:48PM (1 child)
Who boy, thought those were supposed to break at some point.
This definitely won't be abused!
(Score: 2) by coolgopher on Thursday March 05 2020, @01:13AM
systemd won't take no for an answer. We should know this by now...
(Score: 4, Funny) by Anonymous Coward on Wednesday March 04 2020, @06:35AM
I get nervous when I see "The following options are understood".
It kind of implies that there are more options that could not be understood.
(Score: 0) by Anonymous Coward on Wednesday March 04 2020, @06:36AM
You bastard!
(Score: 3, Insightful) by gtomorrow on Wednesday March 04 2020, @08:18AM (8 children)
Wow! That was just so...spiteful!
Apparently, posts don't have a character limit or abbreviate to a "more..." link like articles do.
(Score: 0) by Anonymous Coward on Wednesday March 04 2020, @03:59PM
The poster could have been polite and put that "book" inside a spoiler tag...but it seems that many people never learned good manners.
(Score: 3, Funny) by DannyB on Wednesday March 04 2020, @05:51PM (3 children)
You mean . . . +1 inspiteful.
To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 2) by gtomorrow on Wednesday March 04 2020, @07:47PM (2 children)
Danny, do you stay up all night to invent these horrible puns or do they just come extemporaneously? 🤣
(Score: 2) by DannyB on Wednesday March 04 2020, @09:43PM (1 child)
They come naturally. On the fly.
To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 2) by hendrikboom on Thursday March 05 2020, @12:02AM
I believe that. I once had a friend who claimed his head was in the Cosmic Pun Stream. Very few of his sentences were without puns.
(Score: 0) by Anonymous Coward on Wednesday March 04 2020, @06:11PM (2 children)
AC who posted the man page here.
Don't blame me, Gaark *asked* for it [soylentnews.org].
(Score: 2) by gtomorrow on Wednesday March 04 2020, @07:50PM (1 child)
Oh, well then.
Remind me to never wish for a million dollars to rain on me. You'd probably deliver in pennies.
(Score: 0) by Anonymous Coward on Wednesday March 04 2020, @08:24PM
In rolls too, to make sure there were some skull fractures involved.
wink, wink, nudge, nudge ;)
(Score: 2) by DannyB on Wednesday March 04 2020, @05:53PM
I propose a project to format the systemd man pages as ASCII art and maintain them that way. Sponsored by The
MicrosoftLinux Foundation.To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 2) by driverless on Wednesday March 04 2020, @01:42PM (5 children)
Any Gnu utility (coreutils) must have command line options that consist of the union of every feature ever requested by any user of that utility ever. Says so in the appendix to the apocrypha to the Gnu Manifesto.
You know you're in Bizarro World when the 'true' command, whose function is described as "do nothing" and which should consist of exactly one line of code aside from the main() wrapper, namely 'return(EXIT_SUCCESS)', has been extended to include command-line options [man7.org]. It's sixty-five fucking lines of code [github.com], of which one line is what's required for the 'true' command and the other 64 are bloat.
(Score: 2) by driverless on Wednesday March 04 2020, @01:46PM
Oh yeah, forgot to add:
except for 'true', which was:
until it became part of coreutils.
(Score: 2) by meustrus on Wednesday March 04 2020, @03:19PM (2 children)
The options for `true` are `--help` and `--version`. This raises the question: why wasn't the man page good enough?
I might speculate lack of `man` on all platforms, mainly because I am always annoyed by the lack of it in my install of MinGW. Then again, given the proliferation of programs that have different ideas on how to ask for help (--help, -h, -help), the idea of adding the option to everything (and in this case, as is common, only one version of it) is rather poorly considered.
If there isn't at least one reference or primary source, it's not +1 Informative. Maybe the underused +1 Interesting?
(Score: 3, Funny) by DannyB on Wednesday March 04 2020, @06:25PM
It seems like true should have a --lie option.
To transfer files: right-click on file, pick Copy. Unplug mouse, plug mouse into other computer. Right-click, paste.
(Score: 0) by Anonymous Coward on Thursday March 05 2020, @12:32AM
I kind of like git's approach. `git --help merge` opens the man page for git merge.
It looks like bash's builtin for `true` doesn't recognize `--help` or `--version`, I only get output from those flags when I explicitly use `/bin/true`. So there's that, I guess.
(Score: 1, Informative) by Anonymous Coward on Wednesday April 01 2020, @12:35AM
Much of the early GNU "bloat" comes from trying to merge all the variations of *nix found across the various mainframe and workstation vendors.
This in the hopes of enticing sysadmins to quietly adopt GNU by being a drop in replacement.